Facile mechanochemical cycloreversion of polymer cross-linkers enhances tear resistance.

The mechanical properties of covalent polymer networks often arise from the permanent end-linking or cross-linking of polymer strands, and molecular linkers that break more easily would likely produce materials that require less energy to tear. We report that cyclobutane-based mechanophore cross-linkers that break through force-triggered cycloreversion lead to networks that are up to nine times as tough as conventional analogs. The response is attributed to a combination of long, strong primary polymer strands and cross-linker scission forces that are approximately fivefold smaller than control cross-linkers at the same timescales. The enhanced toughness comes without the hysteresis associated with noncovalent cross-linking, and it is observed in two different acrylate elastomers, in fatigue as well as constant displacement rate tension, and in a gel as well as elastomers.

Synthesis and Ring-Opening Metathesis Polymerization of a Strained trans-Silacycloheptene and Single-Molecule Mechanics of Its Polymer.

The cis- and trans-isomers of a silacycloheptene were selectively synthesized by the alkylation of a silyl dianion, a novel approach to strained cycloalkenes. The trans-silacycloheptene (trans-SiCH) was significantly more strained than the cis isomer, as predicted by quantum chemical calculations and confirmed by crystallographic signatures of a twisted alkene. Each isomer exhibited distinct reactivity toward ring-opening metathesis polymerization (ROMP), where only trans-SiCH afforded high-molar-mass polymer under enthalpy-driven ROMP. Hypothesizing that the introduction of silicon might result in increased molecular compliance at large extensions, we compared poly(trans-SiCH) to organic polymers by single-molecule force spectroscopy (SMFS). Force-extension curves from SMFS showed that poly(trans-SiCH) is more easily overstretched than two carbon-based analogues, polycyclooctene and polybutadiene, with stretching constants that agree well with the results of computational simulations.

Pendant Group Modifications Provide Graft Copolymer Silicones with Exceptionally Broad Thermomechanical Properties.

Graft copolymers offer a versatile platform for the design of self-assembling materials; however, simple strategies for precisely and independently controlling the thermomechanical and morphological properties of graft copolymers remain elusive. Here, using a library of 92 polynorbornene-graft-polydimethylsiloxane (PDMS) copolymers, we discover a versatile backbone-pendant sequence-control strategy that addresses this challenge. Small structural variations of pendant groups, e.g., cyclohexyl versus n-hexyl, of small-molecule comonomers have dramatic impacts on order-to-disorder transitions, glass transitions, mechanical properties, and morphologies of statistical and block silicone-based graft copolymers, providing an exceptionally broad palette of designable materials properties. For example, statistical graft copolymers with high PDMS volume fractions yielded unbridged body-centered cubic morphologies that behaved as soft plastic crystals. By contrast, lamellae-forming graft copolymers provided robust, yet reprocessable silicone thermoplastics (TPs) with transition temperatures spanning over 160 °C and elastic moduli as high as 150 MPa despite being both unentangled and un-cross-linked. Altogether, this study reveals a new pendant-group-mediated self-assembly strategy that simplifies graft copolymer synthesis and enables access to a diverse family of silicone-based materials, setting the stage for the broader development of self-assembling materials with tailored performance specifications.

Operation Mechanism in Hybrid Mg-Li Batteries with TiNb2O7 Allowing Stable High-Rate Cycling.

We studied the structural evolution and cycling behavior of TiNb2O7 (TNO) as a cathode in a nonaqueous hybrid dual-salt Mg-Li battery. A very high fraction of pseudocapacitive contribution to the overall specific capacity makes the material suitable for ultrafast operation in a hybrid battery, composed of a Mg-metal anode, and a dual-salt APC-LiCl electrolyte with Li and Mg cations. Theoretical calculations show that Li intercalation is predominant over Mg intercalation into the TNO in a dual-salt electrolyte with Mg2+ and Li+, while experimentally up to 20% Mg cointercalation was observed after battery discharge. In hybrid Mg-Li batteries, TNO shows capacities which are about 40 mA h g-1 lower than in single-ion Li batteries at current densities of up to 1.2 A g-1. This is likely due to a partial Mg cointercalation or/and location of Li cations on alternative crystallographic sites in the TNO structure in comparison to the Li-intercalation process in Li batteries. Generally, hybrid Mg-Li cells show a markedly superior applicability for a very prolonged operation (above 1000 cycles) with 100% Coulombic efficiency and a capacity retention higher than 95% in comparison to conventional Li batteries with TNO after being cycled either under a low (7.75 mA g-1) or high (1.55 A g-1) current density. The better long-term behavior of the hybrid Mg-Li batteries with TNO is especially pronounced at 60 °C. The reasons for this are an appropriate cathode electrolyte interface containing MgCl2 species and a superior performance of the Mg anode in APC-LiCl electrolytes with a dendrite-free, fast Mg deposition/stripping. This stable interface stands in contrast to the anode electrolyte interface in Li batteries with a Li anode in conventional carbonate-containing electrolytes, which is prone to dendrite formation, thus leading to a battery shortcut.

Synthesis and Assembly of Designer Styrenic Diblock Polyelectrolytes.

Harnessing molecular design principles toward functional applications of ion-containing macromolecules relies on diversifying experimental data sets of well-understood materials. Here, we report a simple, tunable framework for preparing styrenic polyelectrolytes, using aqueous reversible addition-fragmentation chain transfer (RAFT) polymerization in a parallel synthesis approach. A series of diblock polycations and polyanions were RAFT chain-extended from poly(ethylene oxide) (PEO) using (vinylbenzyl)trimethylammonium chloride (PEO-b-PVBTMA) and sodium 4-styrenesulfonate (PEO-b-PSS), with varying neutral PEO block lengths, charged styrenic block lengths, and RAFT end-group identity. The materials characterization and kinetics study of chain growth exhibited control of the molar mass distribution for both systems. These block polyelectrolytes were also demonstrated to form polyelectrolyte complex (PEC) driven self-assemblies. We present two simple outcomes of micellization to show the importance of polymer selection from a broadened pool of polyelectrolyte candidates: (i) uniform PEC-core micelles comprising PEO-b-PVBTMA and poly(acrylic acid) and (ii) PEC nanoaggregates comprising PEO-b-PVBTMA and PEO-b-PSS. The materials characteristics of these charged assemblies were investigated with dynamic light scattering, small-angle X-ray scattering, and cryogenic-transmission electron microscopy imaging. This model synthetic platform offers a straightforward path to expand the design space of conventional polyelectrolytes into gram-scale block polymer structures, which can ultimately enable the development of more sophisticated ionic materials into technology.